I’ve examined many cinewhoops previously few years, and the GEPRC CineBot25 is probably my present favourite 2.5″ cinewhoop. A lot thought has gone into its design, and the eye to element is just wonderful. Whereas it’s not good and has a number of annoying points, as you’ll uncover on this assessment, these quirks don’t detract from its spectacular efficiency.
Study Cinewhoops: https://oscarliang.com/cinewhoop/
The place to Purchase?
You will get the GEPRC CineBot25 from these distributors:
There are two variations: Normal (non-S) and Sport (S). The S model options bigger 1505 4300KV motors, that are an improve from the 1404 motors in the usual model, delivering extra energy and stability.
Batteries are usually not included, my suggestions are the Lava 4S 850mAh:
Get some spare propellers if you happen to plan to crash 🙂
Specs
- Body: GEP-CT25 Gray
- Wheelbase: 115mm
- Flight Controller (FC): TAKER G4 45A AIO
- MCU: STM32G473CEU6
- Gyro: ICM 42688-P
- Firmware: TAKERG4AIO
- Motor: SPEEDX2 1505 4300KV
- ESC: BLHeli 32-bit 45A
- Propellers: HQProp DT63mm x4
- Connector: XT30
- Official Weight:
- Normal PNP Model: 138g ±1g
- Sport PNP Model: 145g ±1g
- Really helpful Battery: 4S 650mAh – 850mAh LiPo
Nearer Take a look at the Construct High quality
The GEPRC CineBot25 S stands out with a sturdy, smooth design. The digicam, motor, and flight controller are mounted on the highest plate, which is comprised of smooth-layered carbon fiber, providing a light-weight but sturdy really feel.
Under the highest plate is a detachable plastic housing for the VTX and receiver. The digital parts are properly protected, however the enclosed design may compromise cooling in scorching environments.
The FPV digicam is mounted inside a devoted soft-mounted cover that limits excessive digicam angles however presents sufficient safety.
An exterior HD digicam could be hard-mounted utilizing the offered adapter, nevertheless it’s finest to keep away from including further weight like a unadorned GoPro. Whereas it might work for sluggish and regular indoor pictures, it compromises outside agility and velocity. The DJI O3 system already gives glorious picture high quality anyway.
Two battery straps of various lengths are included: an extended one for 4S 750mAh and 850mAh batteries, and a shorter one for smaller 4S 650mAh batteries. The drone weighs round 153 grams with out the battery, digicam, and VTX, which is sort of 10 grams heavier than the BetaFPV Pavo25 V2. Nevertheless, this added weight is comprehensible given the additional plastic used for cover.
With the DJI O3 system put in and a 4S 850mAh LiPo, the overall weight is round 290 grams.
Listed below are some aspect by aspect comparisons to the BetaFPV Pavo25 V2:
DJI O3 Setup
Though the CineBot25 helps varied FPV methods, together with analog and Runcam Hyperlink/Wasp, the soft-mounted digicam platform is a transparent indication that it’s particularly designed for the DJI O3 system. Different FPV cameras aren’t as prone to jello and vibration because the O3, making extra gentle mounting obligatory. I actually like GEPRC’s implementation utilizing silicone balls as it really works exceptionally properly.
Nevertheless, the digicam cover can simply pop off throughout crashes, and it’s difficult to reattach as a consequence of how tiny and gentle these silicone balls are. They’re additionally fairly fragile, metallic instruments can simply pierce by them. Whereas GEPRC gives some instruments to assist with this, it’s a trouble remembering to carry them alongside. Zip ties can safe them however will scale back the effectiveness of the gentle mounting.
Consumer Pleasant Design
Among the finest design features of the CineBot25 is how straightforward it’s to entry the flight controller and DJI O3 USB port. There’s a USB-C port on the rear of the drone, related to the flight controller through an extension board.
You possibly can entry the DJI O3’s SD card slot and USB-C port by a cutout within the plastic housing, and when not in use, you’ll be able to put the rubber cowl again on to guard it from grime and water.
There’s no must disassemble the drone or use an adapter to entry these USB ports, making it extremely handy. You possibly can inform how a lot thought has gone into the design.
Nevertheless, one small problem is that I couldn’t join or flash the ESC through the USB port on the FC extension board. I had to make use of the precise USB port on the FC, which requires disassembling the drone. They may have used a USB-C extension cable like Speedybee did within the Bee35 to keep up compatibility. Nevertheless it’s not a giant deal because you don’t usually must flash your ESC.
Dissembling the drone for restore is simple too.
Right here’s a detailed up shot of the flight controller.
Flight Efficiency
The CineBot25 S is just among the best flying 2.5-inch cinewhoops I’ve examined—very steady, well-tuned, and with loads of energy for freestyle.
It’s additionally very environment friendly. I examined mine with LAVA 4S 850mAh LiHV batteries from BetaFPV and bought round 5 to six minutes of flight time (a mixture of aggressive flying and cruising), which may be very spectacular.
The DJI O3 VTX system, paired with a soft-mounted digicam, gives crisp FPV footage with none jello.
The best way to Setup
Though initially I used to be impressed by the CineBot25’s design, the setup course of took a bit extra time and effort than anticipated.
O3 Set up
Very first thing is to put in the DJI O3 system contained in the plastic housing. Sadly, there’s no instruction offered, so that you’ll want to make use of your creativeness. I have to admit it wasn’t straightforward in any respect as I spent over nearly an hour looking for one of the best ways to mount the O3. Ultimately I made a decision to not use the offered heatsink and simply mounted the O3 immediately contained in the plastic housing.
Additionally, not like BetaFPV’s cinewhoops, GEPRC doesn’t present any cable for the O3, however you should utilize the unique cable, so it’s not an enormous problem if you happen to nonetheless have it. Additionally there’s no screws offered for mounting the digicam within the cover – you will have M2 3mm.
Lastly, be sure that to tape the UFL extension to keep away from electrical shorts! It they touches the uncovered battery solder pads might fry your O3!
Binding Receiver
Right here I encountered one other problem – the receiver doesn’t get energy from the USB port, you will need to plug in a battery.
I used to be going to flash the newest ExpressLRS firmware to the receiver together with my binding phrase, so I wanted to seek out out what goal it makes use of. That was completed by going into WiFi mode (by plugging in battery and wait 60 seconds) and checking on the Net UI .
Receiver goal is: Generic ESP8285 PA 2.4Ghz RX, it comes with 3.3.1 firmware.
Nevertheless, I couldn’t discover this goal within the newest ExpressLRS Configurator, so I didn’t replace the firmware however set the binding phrase within the Net UI.
Betaflight Configuration
Organising Betaflight for maiden flight was easy.
The CineBot25 comes with Betaflight 4.5.0. The flight controller goal is TAKERG4AIO. You will discover the unique CLI diff right here (hyperlink to be added).
- In Preset tab, apply ExpressLRS Preset based mostly on the packet fee of your alternative.
- In PID Tuning tab, set your personal charges.
- In Modes tab, assign change for arming.
- In OSD tab, configure OSD components. Though HD was chosen, the canvas was caught in analog dimension. I needed to de-select and choose HD once more to get the bigger HD OSD canvas.
Conclusion
I’m blown away by the GEPRC CineBot25 S—it has among the best design in the marketplace, and the flight efficiency is great! Whereas there are a number of hurdles to beat throughout setup, these are usually not deal breakers. When you’re searching for a 2.5-inch cinewhoop for the DJI O3 system, that is the one I’d advocate proper now.
Get the GepRC Cinebot25 from these distributors:
Get some Lava 4S 850mAh batteries:
Get some spare propellers:
Nevertheless, this drone isn’t designed for sub-250 grams in thoughts. You can most likely push it underneath 250 grams by going analog or utilizing a smaller battery, however you’d be higher off with a 2-inch quad as a substitute (try the Pavo20). I additionally don’t advocate utilizing a GoPro on the CineBot25; it kills its flight efficiency and flight time. If you wish to use a GoPro, go for a 3-inch or 3.5-inch quad.
For cinematic FPV flying and dynamic pictures utilizing the O3, the CineBot25 S presents improbable design and efficiency at a good value level. With its highly effective motors and DJI O3 compatibility, it stands out as a robust contender within the cinewhoop market.