I used to be wanting to assessment the Flywoo Flylens75, particularly given my fondness for its bigger sibling, the Flylens85. The Flylens 75 promised a mix of light-weight design and energy in a 2S, 2-inch drone kind issue. It’s a micro cinewhoop that’s designed for the DJI O3 Air Unit. On this assessment we are going to discover its capabilities and efficiency.
Be taught extra about Cinewhoops in our purchaser’s information: https://oscarliang.com/cinewhoop/
The place To Purchase?
Get your Flylens75 from:
Within the field, it included quite a lot of equipment like spare screws, spare propellers, a 3D printed O3 digicam protector, touchdown foam pads, and battery connectors. My assessment unit additionally got here with two LiPo batteries which must be bought individually.
Construct and Design
The Flylens 75 is notably lighter than the bigger Flylens 85. The drone with DJI O3 Air unit (with out battery), weighing 82g, was impressively mild. It’s about 10 grams heavier than the BetaFPV Pavo Pico although, which is one other cinewhoop of the identical measurement.
The body is crafted from mild but sturdy plastic, that includes versatile and crash-resistant prop ducts. The body encompasses a Y-structure design, guaranteeing that the prop guards don’t intrude with the digicam.
Curiously, the electronics are precisely the identical because the Flylens85, similar FC/ESC board, even motor measurement and KV are the identical. It is because the Flylens75 is utilizing smaller 4-blade propellers as an alternative of bigger 2-blade props within the Flylens 85.
The FC is the Goku F4 12A 1-2S flight controller with built-in 2.4GHz ExpressLRS receiver. The motors are sturdy 1003 14800KV. The propellers are 1.6-inch Gemfan 4-blade props.
It comes with 3D printed TPU battery mounts, supporting battery choices just like the 2S 550mAh, 750mAh and 1000mAh. Nevertheless, it appears you may solely mount the battery sideway (aka rest room tank mounting), for those who mount it entrance to again, it poses potential dangers of scratching the battery towards the USB port.
Putting in DJI O3
The FlyLens 75 is designed to work with each the total and bare variations of the DJI O3 digicam (utilizing Flywoo’s personal O3 Lite equipment).
Putting in the DJI O3 was easy, and the underside mount supplied quick access to the micro SD card and USB-C slot.
Flight Expertise
On its maiden flight, the Flylens 75 showcased outstanding management and stability. Regardless of the compact measurement, the drone managed to deal with windy situations outside. Nevertheless, the battery life was reduce considerably when flying outside particularly when it’s windy.
The drone flew quietly and effectively indoor. In angle mode, navigating tight areas with ease. Indoor flight time is round 4 to five minutes on 2S 750mah and three to 4 minutes on 550mAh.
Personally I choose the way it handles with the bigger 2S 750mAh battery, suggesting that it may be tuned for a barely heavier setup.
The right way to Setup
It got here with Betaflight 4.4.2, flight controller goal is FLYWOOF405S_AIO. Authentic CLI dump might be discovered right here.
Bind receiver following this information https://oscarliang.com/bind-expresslrs-receivers/ In the event you want to flash receiver firmware, the Gadget is Flywoo EL24P 2400 RX.
For my first flight, I modified the next settings:
- Within the Configuration tab, I adjusted the Arming Angle to 180 levels.
- Within the Modes tab, I configured switches for arm and angle modes.
Conclusion
The Flywoo Flylens75 stands out as a formidable micro Cinewhoop. Its capability to hold a full DJI O3 digicam, mixed with its distinctive flight stability and quiet operation, makes it a superb alternative for indoor flying and tight-space navigation. Whereas there are minor drawbacks, resembling the shortage of energy and flight time in outside atmosphere, the drone’s total efficiency and capabilities make it a high contender within the 1.6-inch Cinewhoop class.
Get your Flylens75 from: